Bike Talk Motorcycle Forum Bike Talk Motorcycle Forum
Go Back   Bike Talk Motorcycle Forum > The Garage > Motorcycle Tech Talk
Discussion on Sportster info within Bike Talk's Motorcycle Tech Talk forum.

Home Forum Register FAQ Sponsorship Search Today's Posts Mark Forums Read

Sportster info


Welcome to the Bike Talk motorcycle forum Contact Bike Talk Join Bike Talk

» Site Navigation
 > F.A.Q.
» Auction

» B-T Recommends:
Visit Biker Bids

Harley-Davison Parts & Accessories at RideGear.com


Reply
 
Old May 10th, 2008, 07:03 AM   #1
gabby
Rookie 10+ posts
 
Join Date: Jan 2006
Posts: 27

in 88, what inch sporty was out. also, the oil line to the head, does the head have to be removed to change the "o" ring? a friend is looking to buy a 1988 sporty with a leak, but is getting conflicting info. thanks gabby (it sucks to be stopid)
gabby is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Sponsored Links
Old May 10th, 2008, 09:50 AM   #2
cowboy
Has posted 500+
 
cowboy's Avatar
 
Join Date: Apr 2006
Location: Alvin TX
Posts: 1,729
Model: 03 E Glide X cop bike
Interests: My family Old Dodge truck's Riding My Glide
Occupation: Retired truck Driver
gabby I think both the 883 & 1200 where the sporty's for 88 , as for the O ring not sure But A O ring would not work in a head as for the heat , might be just the top rocker box has to come off to replace it
cowboy is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old May 10th, 2008, 09:51 AM   #3
SPORSTERBOY
Has posted 500+
 
SPORSTERBOY's Avatar
 
Join Date: Mar 2006
Location: lake jackson,tx
Posts: 912
Model: 03 883 XLC-CHOPPER
Occupation: welder
View SPORSTERBOY's Gallery
11 Images Posted
Had A 89, There Was A 883,and 1200, Same Basic Design Till O3. Evo Sportys. Don't Recal Any Oil Line Going To The Heads, The Crank Case Breather Line Comes Out Of The Case Up To The Ac, Instead Of The Head Bolts. The Only O Rings I Can Think Your Talking About Is The Ones At The Base Of The Push Rods, I Had This Leaky Problem There. If This Is The Case You'll Have To Pull The Rocker Box Covers To Change Out The O Ring, And Since Your Going To Be Half Way There My As Well Do The Hole Top End Gasket Job, Fairly Simple If You Have The Right Tools, Allen Wrenches For Most Of The Outside, The Only Special Tool You'll Need Is For The Jugs, It's Like A 8 Star Sockethead Bolt.
SPORSTERBOY is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old May 10th, 2008, 10:35 AM   #4
gabby
Rookie 10+ posts
 
Join Date: Jan 2006
Posts: 27

thank you cowboy and sportsterboy, this clears alot.didn't think the oil line would be a problem. just wanted to know what he may really be dealing with. he was told it would take 300 to fix. guess with the price of shop labor this could be right. again thanks gabby
gabby is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old May 10th, 2008, 03:10 PM   #5
Art_NJr
200+ posts and climbing
 
Join Date: Mar 2008
Location: North Carolina
Posts: 457
Model: '95, '00 Sportsters
Interests: Land-Speed-Record events
Occupation: Independent contractor (several fields)
View Art_NJr's Gallery
4 Images Posted
Quote:
in 88, what inch sporty was out.
883 & 1200 models (1200 replaced the 1100). Differences in cylinder bore (3" vs. 3.5") & combustion chambers/valves, but everything else the same (cases, flywheels, rods, stroke, trans., etc.).

Quote:
also, the oil line to the head, does the head have to be removed to change the "o" ring?
There is no external oil line to the head as on several earlier H-D models - oil goes up thru the pushrods/tubes. The pushrod tubes have O-rings top & bottom & those can go bad. I'm almost positive '88 models had collapsible pushrod tubes rather than 1-piece as on later models - I say that because my race engine is based on the '86-'90 case design & when building it, I bought collapsible pushrod tubes for those year models.

That design makes the O-rings a lot easier to change out because you don't have to take anything else apart if you have adjustable pushrods & can shorten them up enough to pull them out from the right side of the engine. If not, you have to pull the rocker boxes, loosen up the rocker arms & pull the pushrods out the top.

However, there is a trick I've used - pull the pushrod tubes, cut the O-rings with a razor-knife & remove them. Then clean everything up very, very good. Then take your new O-rings & very carefully, with a new razor blade, cut the new O-rings @ a 45-degree angle @ one point in the circle - so you can open up the new O-ring to get it around the pushrod. Then ease it into place & get it seated properly so the cut will line back up perfectly & disappear.

You have to take your time with this & you need to coat the area where the O-ring seats & the O-ring itself with a heavy straight-weight oil, like Valvoline Racing Oil, SAE 50, or even 60. But if you do it right, the cut O-ring will seal right back up @ the cut. Put the pushrod tubes back on carefully so you don't dislodge the O-rings & you're good to go.

Start the engine & see if you get any oil seepage where a pushrod tube goes into a tappet block - if you do, you'll have to do the job over again. But it's worked for me & on an engine that flows a heck of a lot more oil than a stock one does.
Art_NJr is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old May 10th, 2008, 04:22 PM   #6
SPORSTERBOY
Has posted 500+
 
SPORSTERBOY's Avatar
 
Join Date: Mar 2006
Location: lake jackson,tx
Posts: 912
Model: 03 883 XLC-CHOPPER
Occupation: welder
View SPORSTERBOY's Gallery
11 Images Posted
THAT'S A NIFFTY TRICK THERE, HAVE TO REMEMBER THAT ONE, YA KNOW HOW I'M ALL ABOUT SHORT CUTS
SPORSTERBOY is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Reply

«- Efi remapping « Previous | Next » Hot Harley -»



Thread Tools



Similar Threads to: Sportster info
Thread Thread Starter Forum Replies Last Post
Rim info fireart Motorcycle Tech Talk 4 Dec 26th, 2007 10:54 AM
Oil Drain info 99 Softail Custom Motorcycle Tech Talk 4 Apr 13th, 2006 09:45 PM
Need oil change info Silverbullet Motorcycle Tech Talk 6 Oct 27th, 2004 08:51 PM
HD mechanic info HDwannabe The Welcome Mat 1 Sep 1st, 2004 01:30 AM
need info on sportster that has mostly new parts but wont crank jlatimer Pull up a chair and sit for a spell 1 Jun 1st, 2004 03:14 PM

Powered by vBadvanced CMPS v3.0 RC1

All times are GMT -7. The time now is 05:52 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.0.0 RC8
BikeTalk Motorcycle Forum Copyright 1997-2008 all rights reserved


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104