1. After 20+ years it's time to pass the torch. If you are interested in acquiring this forum please contact support@cv-performance.com for details. Any spam will be reported and blocked.
  2. Welcome to Bike Talk, a forum for all bikers and motorcycle enthusiasts. If you are new to Bike Talk, be sure to register for free and join the conversation.

    There's always someone around willing to help out with questions or give a friendly wave back. All Harley and metric riders are welcome.
Bike Talk Motorcycle Forum is For Sale Welcome to Bike Talk

Air Compressor

Discussion in 'Motorcycle Tech Talk' started by Informme, Feb 5, 2011.

Page 2 of 3
  1. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    get the best compressor you can afford. the key to look for is cfm at a certain psi. the higher the cfm the better. both oil and oilless compressors will make water. the best way to trap it is with a water trap away from the compressor, before the tool you are using. drain the tank at least weekly, daily is better. both of my compressors are piston, with a crankcase with oil. just like a internal combustion engine, when rings wear you will start pumping oil. if the compressor has some quality to it you can rebuild it, if not ya throw it away and get another.
    chucktx, Feb 7, 2011
    #21
  3. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    if you use plastic pipe, and i did, dont mount it where it can get hit. if it gets hit it will explode with lots of shrapnel!!!
    chucktx, Feb 7, 2011
    #22
  4. ironhorse

    ironhorse Active Member

    Joined:
    Sep 20, 2006
    Messages:
    1,290
    Likes Received:
    5
    Location:
    I'm everywhere, I'm everywhere
    Like chuck said It's what you can afford. I gave my old craftsman oilless just after I rebuilt it my complaint was the noise I'd roll it outside and shut the door. You can find good deals on Craigslist list eBay and garage sales
    ironhorse, Feb 7, 2011
    #23
  5. Informme

    Informme New Member

    Joined:
    Aug 11, 2010
    Messages:
    111
    Likes Received:
    0
    Location:
    Western NC
    I'm glad you mentioned that because I am sure I would have used plastic as well.
    Informme, Feb 7, 2011
    #24
  6. Informme

    Informme New Member

    Joined:
    Aug 11, 2010
    Messages:
    111
    Likes Received:
    0
    Location:
    Western NC
    Thanks again for all the help.
    Informme, Feb 7, 2011
    #25
  7. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    as long as the plastic is protected.....no problem. just dont get too mad and throw hammers.........:eek:
    chucktx, Feb 8, 2011
    #26
  8. FLHTbiker

    FLHTbiker Moderator Staff Member

    Joined:
    Nov 3, 2004
    Messages:
    18,516
    Likes Received:
    252
    Location:
    Oregon
    Cast iron pipes would work. Copper is to expensive and it corrodes.
    FLHTbiker, Feb 8, 2011
    #27
  9. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    true....be sure to put drains in the lower parts of your run......
    chucktx, Feb 9, 2011
    #28
  10. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    after time, cast iron will rust from moisture. this may take years, or less.......keep an eye on it.
    chucktx, Feb 9, 2011
    #29
  11. Informme

    Informme New Member

    Joined:
    Aug 11, 2010
    Messages:
    111
    Likes Received:
    0
    Location:
    Western NC
    I sure will.

    Thanks
    Informme, Feb 9, 2011
    #30
  12. JohnnyBiker

    JohnnyBiker Well-Known Member

    Joined:
    Mar 25, 2010
    Messages:
    9,568
    Likes Received:
    205
    Location:
    Minnesota
    I like whatever works. :D
    JohnnyBiker, Feb 9, 2011
    #31
  13. FLHTbiker

    FLHTbiker Moderator Staff Member

    Joined:
    Nov 3, 2004
    Messages:
    18,516
    Likes Received:
    252
    Location:
    Oregon
    Some of that plastic crap isn't designed for high pressures either so be careful if you go with the plastic route.
    FLHTbiker, Feb 9, 2011
    #32
  14. cardboard

    cardboard Well-Known Member

    Joined:
    Nov 12, 2007
    Messages:
    11,459
    Likes Received:
    56
    Location:
    Lake Livingston, Tx.
    Mine has been down stairs for a few years.

    think I used plastic hotwater pipin.
    cardboard, Feb 9, 2011
    #33
  15. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    the black schedule 80 works good......but warnings still apply.....
    chucktx, Feb 9, 2011
    #34
  16. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    i used schedule 40...standard pvc....it is rated for 250psi i believe. keep my air at 150....
    chucktx, Feb 9, 2011
    #35
  17. cowboy

    cowboy Moderator Staff Member

    Joined:
    Apr 19, 2006
    Messages:
    9,926
    Likes Received:
    50
    Location:
    Alvin TX
    No matter what pipe you use , you'll still need a drain , cause the water build up will get in your tools & freze in the winter :eek:
    cowboy, Feb 9, 2011
    #36
  18. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    yup!
    chucktx, Feb 9, 2011
    #37
  19. FLHTbiker

    FLHTbiker Moderator Staff Member

    Joined:
    Nov 3, 2004
    Messages:
    18,516
    Likes Received:
    252
    Location:
    Oregon
    That's right it does freeze down there in Texass :roflmao:
    FLHTbiker, Feb 9, 2011
    #38
  20. chucktx

    chucktx Moderator Staff Member

    Joined:
    Jul 5, 2005
    Messages:
    12,545
    Likes Received:
    10
    hard to believe your warmer than we are!!!!!!!
    chucktx, Feb 9, 2011
    #39
  21. FLHTbiker

    FLHTbiker Moderator Staff Member

    Joined:
    Nov 3, 2004
    Messages:
    18,516
    Likes Received:
    252
    Location:
    Oregon
    Man it was so nice here today, full sun. I went out for a ride today, gas mileage is up to 38, getting better.
    FLHTbiker, Feb 9, 2011
    #40
Page 2 of 3

Share This Page

XenPorta © Jason Axelrod from 8WAYRUN.COM